A range of damp proofing materials available from Stoke-on-Trent 

Triton’s “new generation” DPC formula is a ready to use, water based and water-soluble thixotropic gel which diffuses naturally into damp substrates. After injection, Tri-Gel reacts to form a water repellent silicone resin network within the capillaries of the substrate. This network is permeable to water vapour which means that the walls can “breathe” and dry out naturally. The formulation is not reliant on alkalinity for effective curing. Tri-Gel can be used effectively to treat brick, stone and other substrates.

A unique silicone emulsion cream for injection into brickwork etc. for the control of rising dampness. Tri-Cream can be used in all types of masonry without the use of high pressure equipment. The cream is delivered by hand pressure from a simple displacement pump and injector lance into a series of holes drilled into the mortar course.

Triject 3 can be injected into pre-drilled holes formed either in the bricks or the mortar joints to form a continuous barrier against water rising from the ground. Within the walls, Triject 3 reacts with carbon dioxide to form a permanent water repellent coating within the capillaries of the masonry.

A single component, polymer modified cement “tanking” system for walls and floors, designed to be applied as a waterproof slurry. TT 55 is a highly effective damp proof membrane for brickwork, concrete or any cementitious substrate. Surfaces to be treated with TT55 should be correctly prepared, free from all loose materials and contaminants and be in a sound and solid condition. For application to floors, TT55 should be applied directly to the structural slab. For wall applications, TT55 should be sandwiched between sand/cement render coats. For all TT55 applications, special attention should be given to wall/floor junctions.

Stormdry Is a deeply penetrating water repellent cream for brick, stone and concrete. Due to its cream-based formulation it is able to penetrate more deeply into masonry than standard liquid-applied. Water seal products. Stormdry is based on proven silane/siloxane technology and works by lining the pores of the masonry rather than blocking them – allowing the wall to continue to breath. Stormdry is easy to apply using a brush or roller and only a single coat application is required.

A water and salt resistant additive for cement mortars. Improves workability of the mix. Particularly recommended for use in mortars used for internal cement rendering (replastering) of walls affected by rising dampness. Supplied in concentrate form and diluted for use. Supplied in 5 litre and 25 litre containers.

Used for the control and long term protection against wood boring insects and wood destroying fungi (dry and wet rots). A super concentrate supplied in a small plastic container. The special micro-emulsion formulation leads to a better penetration than obtained with traditional water based emulsified preservatives. It provides the necessary control and long term protection against wood boring insects and wood destroying fungi (dry and wet rots).

A 3mm polypropylene cavity drain membrane suitable for direct plastering. Suitable for use as an isolating plaster membrane following remedial treatments.

Triproof AQ is a highly effective water repellent based on a blend of Silane, Siloxane and Silicone resins. Triproof AQ is suitable for use over masonry, brickwork, concrete and renders. Superior performance is obtained on alkaline surfaces such as new renders and concrete. Triproof AQ is available in concentrate form in 2.5 litre containers.

Dryrod Damp-Proofing Rods are the next generation treatment for rising damp. They provide a higher level of performance and quicker installation speed than any other rising damp treatment currently available.

The patented, internationally tested damp-proofing injection cream for the treatment of rising damp. Dryzone’s high level performance makes it suitable for walls of all types, including cavity and rubble infill,

A salt and damp resistant adhesive glue for fixing plasterboard directly to masonry surfaces. Provides excellent bonding characteristics to the substrate.

A breathable, salt-resistant, water-repellent, that acts as a primer for drygrip adhesive. Applied to walls contaminated with rising damp, the cream greatly weakens the crystal strength of salts forming in or at the masonry surface as damp evaporates. Breathable and long-lasting formulation. Deeply penetrates to form a durable bond with the masonry structure. Easy to apply by brush or roller.

Dryzone Damp-Resistant Plaster — This modern renovation plaster is designed to be highly resistant to both salt and damp transfer. The highly breathable and porous structure of the plaster allows for quick drying after the treatment of rising damp and will stop salt contamination from affecting the decorative surface.